10.0.0.1 Default Username & Password List (2026)
Last updated: June 2026
The most common 10.0.0.1 default password is admin, with the username admin too.
Why Does 10.0.0.1 Need a Default Password?
10.0.0.1 is a private gateway address used by many Piso WiFi machines and some routers. Its panel can change WiFi names, time rates, and speed. So the maker protects it with a login. A simple default lets the first owner get in and set things up.
Think of the default as a temporary key. It should be replaced the moment the device goes into service. Sellers often pre-configure boards first, which is why a buyer’s default may no longer work. Be wary of any post promising a universal master password. No such thing exists.
What Is the 10.0.0.1 Default Username and Password List?
A few login pairs cover almost every device. The pair admin / admin works most often. If it fails, leave the password blank, since many fresh boards ship with none. Older OpenWrt boards may use root. Try them in the order shown below.
| Username | Password | Typical device |
|---|---|---|
| admin | admin | Most Piso WiFi boards and many routers |
| admin | (blank / empty) | Some boards on first boot |
| admin | password | A few generic router firmwares |
| root | admin | Older OpenWrt-based boards |
Usernames are usually lowercase. Type admin exactly as shown, with no capital or trailing space.
How Do You Log In With the Defaults?
Connect to the device’s network and turn off mobile data first. Open a browser and type http://10.0.0.1, using http, not https. When the login box appears, enter admin as the username. Try admin as the password, or leave it blank, then submit.
- Connect your phone or laptop to the network the 10.0.0.1 device broadcasts.
- Turn off mobile data so your phone cannot bypass the gateway.
- Open a browser and type http://10.0.0.1 (use http, not https).
- When the login box appears, enter admin as the username.
- Enter admin as the password, or leave it blank, then tap Login.
- If it is rejected, try the next pair in the table, one at a time.
Once inside, you reach the admin dashboard. For a labelled tour of those screens, see the admin dashboard walkthrough.
What If the Default Password Was Changed?
If none of the defaults work, the password was almost certainly changed. That is normal and good for security. You have two safe options: ask the owner for the current password, or do a factory reset. A reset restores the maker’s default login.
- Ask the owner. If you bought the machine, the seller should give you the current password. This keeps your rates and WiFi name intact.
- Factory reset. Hold the reset button for 10-30 seconds until it reboots. This restores the maker’s default.
A reset also clears time rates and the WiFi name, so treat it as a last resort. Keep the board’s manual nearby, since the button and hold time vary by model.
How Do You Change the Default for Security?
Leaving the login at admin / admin is risky. Any customer could open your panel and give themselves free time. So set a strong password right after your first login. Use at least eight characters and avoid the shop name or 12345678.
Write the new password somewhere safe so you avoid a reset later. Share it only with people who genuinely need admin access. A strong, private password is the single best protection for your machine.
What If the Page Will Not Load at All?
Sometimes the problem is not the password; the page simply will not open. If 10.0.0.1 times out or shows an error, the cause is usually the network. Confirm you are on the right WiFi, use http://, and disable mobile data. A quick restart of the board clears a frozen portal.
- What to do when you cannot reach the panel.
- Steps for when the page is not working.
- How to fix a refused connection error.
Reference: Private network (Wikipedia).
Frequently Asked Questions (2026)
What is the default password for 10.0.0.1?
The most common default is admin for both username and password; on some boards the password is blank. There is no universal secret PIN — those vary by device.
Is admin/admin always the 10.0.0.1 login?
No. admin/admin is the most common factory default, but sellers often change it. If it fails, try a blank password or do a factory reset.
I forgot my 10.0.0.1 password. How do I reset it?
Hold the reset button on the board for about 10–30 seconds until it reboots. This restores the manufacturer default username and password, but also clears your custom settings.
Why does 10.0.0.1 not accept any password?
Either the password was changed, or the page is not really loading the login. Confirm you are connected to the device’s network and using http://10.0.0.1, then retry.
